Check the power supply and thermostat settings if your Reliance water heater is not working. Inspect for any visible damage or leaks.
Reliance water heaters are known for their durability and efficiency. Despite their reliability, issues can occasionally arise, causing inconvenience. Common problems include power supply interruptions, thermostat malfunctions, or sediment buildup. Regular maintenance can prevent most of these issues. Ensuring the unit receives adequate power and checking the thermostat settings are crucial first steps.
Sediment buildup in the tank can also cause heating problems. Flushing the tank periodically can help maintain optimal performance. If these steps do not resolve the issue, professional assistance may be necessary. Proper troubleshooting can save time and restore hot water quickly. Regular checks and maintenance can extend the lifespan of your Reliance water heater.
Credit: www.amazon.com
Page Contents
Common Issues
Check if the pilot light is out. Sometimes, the thermostat setting might be too low. Make sure the circuit breaker is not tripped. Inspect the heating elements for any damage. These steps help in identifying the problem quickly.
A faulty thermostat could cause temperature fluctuations. Sediment buildup in the tank affects heating. Ensure the water heater size matches household needs. Loose wiring might lead to inconsistent temperatures. Proper maintenance helps in avoiding these issues.
Credit: terrylove.com
Initial Checks
Check the power supply and circuit breaker to ensure electricity reaches the Reliance water heater. Verify the thermostat settings and reset if necessary. Inspect the pilot light or ignition system for proper functioning.
Power Supply
Check if the water heater is plugged in. Ensure the circuit breaker is not tripped. Sometimes, a blown fuse can cause issues. Replace the fuse if needed. Verify that the outlet is working by plugging in another device.
Reset Button
Locate the reset button on the water heater. Press it to see if the heater starts working. If the button doesn’t stay in, it might be a bigger issue. Sometimes, the reset button trips due to overheating. Allow the heater to cool before trying again.
Thermostat Problems
The thermostat settings might be wrong. First, check the current temperature setting. Adjust it to your desired temperature. Sometimes, settings can change by mistake. Ensure the thermostat is not set to “vacation mode”. This setting can affect heating. Resetting the thermostat might help too. Follow the manual for exact steps.
A faulty thermostat may need replacement. First, turn off the power to the heater. This step is very important for safety. Remove the old thermostat from the unit. Install the new one according to the instructions. Make sure all wires are connected properly. Turn the power back on and test the heater. If problems persist, you may need professional help.
Credit: www.youtube.com
Heating Element
The heating element might be broken. Use a multimeter to test it. Set the multimeter to the ohms setting. Place one probe on each screw of the heating element. A good heating element shows a reading between 10 and 30 ohms. No reading means it’s broken and needs replacing.
Turn off the power to the heater. Drain the water from the tank. Remove the access panel and insulation. Disconnect the wires from the element. Use a wrench to remove the old heating element. Install the new heating element in its place. Reconnect the wires and replace the insulation and access panel. Fill the tank with water and turn on the power.
Sediment Build-up
Sediment build-up in a Reliance water heater can hinder its performance, leading to inconsistent water heating. Regular maintenance helps prevent this issue and ensures efficient operation.
Draining Tank
First, turn off the water heater. Connect a hose to the drain valve. Place the other end of the hose outside. Open the drain valve to let water out. This removes sediment from the tank. After draining, close the valve. Refill the tank with fresh water. This keeps the heater efficient.
Using Vinegar Solution
Mix vinegar with water in a bucket. Pour the solution into the tank. Let it sit for a few hours. Vinegar helps to break down the sediment. After waiting, drain the tank again. Rinse with fresh water. This method keeps your heater clean.
Pressure Relief Valve
Ensure the water heater is off. Locate the pressure relief valve. This valve is usually on the top or side of the heater. Lift the valve’s lever gently. Listen for a hissing sound. Water should flow out of the pipe. If no sound or water is present, the valve is faulty.
Turn off the water supply. Drain some water from the tank. Use a wrench to remove the old pressure relief valve. Wrap Teflon tape around the threads of the new valve. Screw the new valve into place tightly. Turn on the water supply and check for leaks.
Pilot Light Issues
Always turn off the gas before relighting the pilot. Wait for five minutes. This lets any gas clear out. Find the pilot button on your heater. Press and hold it. Use a lighter or match to light the pilot. Keep holding the button for a minute. This helps the pilot stay lit. Release the button slowly. Check if the pilot stays lit.
Turn off the gas and let the heater cool. Find the pilot orifice. It’s a small hole where the flame comes out. Use a needle or small wire to clean the orifice. Be gentle to avoid damage. Blow away any dust or debris. Turn the gas back on. Relight the pilot as described earlier. A clean orifice helps the pilot light stay strong.
Professional Help
A plumber should be called if the water heater leaks. Strange noises from the heater need a plumber too. If there’s no hot water, call a plumber. Rusty water from the heater is a sign. Plumbers fix water pressure issues. Burning smells from the heater need urgent help.
A good technician has experience with water heaters. Check for certifications before hiring. Read reviews online to find the best. Ask friends for recommendations. Make sure they offer a warranty. Compare prices before deciding. Choose someone available when needed.
Frequently Asked Questions
Where Is The Reset Button On A Reliance Electric Water Heater?
The reset button on a Reliance electric water heater is typically found behind the thermostat access panel. You may need to remove the panel to see it.
Why Would Hot Water Heater Suddenly Stop Working?
A hot water heater may stop working due to a tripped circuit breaker, faulty thermostat, or sediment buildup. Check for leaks, or pilot light issues.
How Do I Reset My Hot Water Heater Not Working?
Turn off the power supply. Locate the reset button on the heater. Press and hold it for a few seconds. Release the button. Restore power and check if the heater works.
Why Does My Reliance Water Heater Keep Turning Off?
Your Reliance water heater may turn off due to a faulty thermostat, sediment buildup, or a malfunctioning pilot light. Regular maintenance and professional inspection can resolve these issues.
Conclusion
A malfunctioning Reliance water heater can disrupt daily routines. Regular maintenance prevents many common issues. If problems persist, consider professional help. Stay proactive to ensure consistent hot water supply. Reliable water heaters enhance comfort and efficiency in your home. Keep your Reliance water heater in top shape for peace of mind.